- #Sunquest tanning bed manuals install
- #Sunquest tanning bed manuals pro
- #Sunquest tanning bed manuals free
- #Sunquest tanning bed manuals crack
#Sunquest tanning bed manuals crack
Not sure if working could not plug in not outlet at my house could be use for parts or could work perfectly crack on top plastic come by and see it give me a offer $500 or OBO.
#Sunquest tanning bed manuals pro
Tanning bed sunquest pro rs 26 - $500 (Port st lucie).It has been sitting in our garage, so it needs a little cleaning up. This is a used tanning bed, but it works great. It was actually never used, since upon arrival it was not installed, and much later discovered that it was not working. This is large, and heavy tanning sunbed, which retailed for over $800. Hi, I am selling a, Tanning Bed SunQuest Pro 24 RSF 220 Volt, In Excellent Condition.
#Sunquest tanning bed manuals free
Free Tanning Bed SunQuest Pro 24 RSF 220 Volt (Miami).Never use with an extension cord unless plug can be fully inserted. If it still does not fit, contact a qualified electrician (you may need to replace your outlet). If the plug does not fit fully in the outlet, reverse the plug. As a safety feature, this plug will only fit in a polarized outlet one way. This product has a polarized plug (one end is wider than the other).
![sunquest tanning bed manuals sunquest tanning bed manuals](http://www.usedbeds.org/bedimages/MontegoBay2400_400.jpg)
Jumper Wire Removed, Remote Timer used in conjunction with on board timer. Plug the power cord into the wall receptacle. Connect canopy and bench cords together white to white and black to black. The backup timer will shut down the bed and is set for the maximum exposure.ħ. This unit is equipped with a with a 24 volt solid state backup timer that cannot be bypassed. NOTE:Save the red jumper wire and tape to back of bed for future use.
#Sunquest tanning bed manuals install
T-Max remove the red jumper wire from the removable section of the plug.ī) Install new timer wires where the red jumper was located. If you are not using a remote be sure that the plugs are attached to each other.Ī) When using a remote timer other than a Remote time port is located at the rear of the bed across from the timer. DO NOT ATTEMPT TO PLUG ANY OTHER DEVICES INTO THESE RECEPTACLES.Ħ. Plug the body fan into the receptacle located beneath the bed. Attach the body fan at either end of the bench using the screws provided. Canopy should stay in the open position.ĥ. Slowly raise canopy, remove 2 x 4's and attach the large end of the piston to the top ball stud. Install the 3/8" bolt though the shoulder washer and bushing. Align the top hole of the hinge with the hole in the canopy. Make sure you line up the rails or the styrofoam will break. Place the canopy CAREFULLYon the Styrofoam or 2x4's that you placed on the bench.
![sunquest tanning bed manuals sunquest tanning bed manuals](https://i.pinimg.com/236x/24/1e/a1/241ea11c332387e031cba7d5de8a932f.jpg)
Remove the 3/8" x 1.5" bolts from the ends. Nylon washers go between the hinge and the bed end cap.ģ.Remove canopy from the box. Remove the 3/8" x 1" bolts from the ends of the lounge. CAUTION: DO NOT REMOVE FOAM PROTECTING THE TIMER, AS THE BUTTONS MAY TEAR WHEN TURNING THE BED OVER.Ģ. Turn bench over so it is standing on the legs. Side skirt installs behind front skirt with the 8 screws provided (you should be able to see into the slotted louvres). Attach the pistons to the ball stud at each end (the smaller shaft is attached to the bench).ġC.Attach front skirt and side skirt. Remove the eight 5/16" x 1 " bolts from the bench panel.ġB.Remove the 42" x 16" pieces of styrofoam from the box and place them across the bench rails (or use 2x4's). Place lounge, bulbs facing down, on a soft surface.
![sunquest tanning bed manuals sunquest tanning bed manuals](https://www.wolfftanning.com/images/content/l-2000s.gif)
General Overview w/ Ballasts & CapacitorsĬlick here for a picture of electrical outlet placementĬlick here for a picture of ideal in-room bed placementġA.Remove lounge from box. As always, please call with any questions ph. In this instance these pictures can be invaluable in locating the correct part. We recognize that you are new to the tanning industry and might not know what all the components look like in a tanning bed. In many cases the replacement parts are small and easily accessible and can be replaced by you or your staff. Occasionally your tanning bed may need to be repaired or parts replaced. This page was designed to assist you in repairing your tanning bed.